Here is the instructions document for the LEGO Old Fishing Store LED lighting kit. Please read and follow the steps carefully to ensure this lighting kit is installed properly.
This user guide is also available to download in PDF format here.
Package contents:
4x White 15cm Bit Lights
3x White Strip Lights
1x 6-Port Expansion Board
1x 30cm Connecting Cable
1x 15cm Connecting Cable
1x 5cm Connecting Cable
1x AA Battery Pack (requires 3x AA Batteries)
OR
1x USB Power Cable
Note – AA Battery Pack will be replaced with USB Power Cables from mid April 2020
LEGO pieces
2x Plates 1×6
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) Start by removing the upper level as well as the main roof section.
Remove the lamp section and then disassemble as per below.
2.) Take a White 15cm Bit Light and then thread the connector side through the hole on top of the bottom piece. Thread it all the way through until the LED is flat against the top of the piece.
You may need bend the LED slightly so that it sits flat against the top of the LEGO piece
Reconnect the top section to secure the LED in place.
Reconnect the lamp back to the desk inside the building ensuring the cable is facing the front left corner so that it is not visible if you look in the window.
3.) Take the top section of the Old Fishing Store and remove the roof.
Disconnect the flat clear 2×2 boat stud piece from underneath the roof and then take a White 15cm Bit Light and place it directly in the centre. Reconnect the flat clear boat stud piece directly over the Bit Light to secure it in place.
Ensure the LED is the correct way facing up
Secure the cable by laying it underneath the bottom brown 1×6 plate.
Ensure the cable is laid in between studs
4.) Before reconnecting the roof, thread the Bit Light cable from the roof down and then pull it out from the bottom of the top section.
5.) Remove the lamp from the bottom of this section and then disconnect the black round stud from underneath.
Take another White 15cm Bit Light and thread the connector side through the top of the black round plate. Thread it all the way through until the LED is flat against the top of the plate then reconnect the top section of the lamp.
You may need bend the LED slightly so that it sits flat against the top of the LEGO piece
6.) Reconnect the lamp to the outside of the upper level and then lay the cable and secure it underneath the brown LEGO 1×6 plate.
7.) Take the 6-Port Expansion Board and then connect the two bit light cables to spare ports.
8.) Take the 30cm Connecting Cable and connect one end to the expansion board.
9.) Take the AA Battery Pack and insert 3x AA Batteries to it before placing it at the back of the old fishing store in the following location. It should seat neatly in between the back of the building and rail.
If you’re using a USB Cable, place this here instead.
10.) Take the entire upper level above the set and take the bit light cable from the lamp inside and connect it to the expansion board.
Take the battery pack / USB cable and connect it to the expansion board.
Tuck the expansion board and excess cables (except for the 30cm cable) up inside the upper level as per below.
Before reconnecting the upper level back to it’s original position, ensure the 30cm connecting cable is pulled across to the right section of the building.
VIEW FROM THE BACK: Ensure 30cm cable is accessible after reconnecting upper level
Test the lights we have installed so far by turning ‘ON’ the battery pack.
If you’re using the USB Power Cable, connect this to a USB Power Bank or wall adaptor (sold separately) and turn it ON to test the front lights are working OK.
11.) Remove the lamp from the right side of the building and then disconnect the black round stud from underneath.
Take another White 15cm Bit Light and thread the connector side through the top of the black round plate. Thread it all the way through until the LED is flat against the top of the plate then reconnect the top section of the lamp.
You may need bend the LED slightly so that it sits flat against the top of the LEGO piece
12.) Remove the following tiles on the wall surrounding where the lamp was connected to.
Reconnect the lamp with bit light installed and then pull the cable behind and up. Lay the cable in between studs before reconnecting the bottom tile we removed earlier.
13.) Continue laying the cable up the side of the wall in between the following studs before reconnecting the tiles over the top.
14.) Turn the building around to the front and remove the “Anton’s Bait Shop” sign from the hinges and then turn the sign section over as per below.
15.) Take 1x White Strip Light and then connect a 15cm Connecting Cable to the left port.
Using it’s adhesive backing, stick the strip light to the bottom of the ‘Anton’s Bait Shop’ sign in the following position.
16.) Take the sign section above the fishing store and then connect the other end of the lamp cable from underneath into the right port of the strip light before reconnecting the sign section back into place.
Tuck in the excess cable from the lamp underneath the sign section as per below:
Pull the 15cm connecting cable from the strip light out so we can connect this later.
17.) Take the main roof section and then turn it over onto its back as per below:
Take the remaining 2x White Strip Lights and stick them to the provided LEGO 1×6 Plates using their adhesive backing.
Take the 5cm Connecting Cable and connect them between the two strip lights.
18.) Mount the two Strip Lights underneath the main roof section in the below position.
19.) Take roof over the fishing store and then connect the other end of the 30cm cable from the left section of the building to the top of the right strip light.
Before reconnecting the roof, take the other end of the 15cm cable below and connect it to the top of the left strip light.
This finally completes installation of the Old Fishing Store Light Kit. Now turn ‘ON’ your light kit and ENJOY!
Here is the instructions document for the LEGO Winter Holiday Train 10254 LED lighting kit. Please read and follow the steps carefully to ensure this lighting kit is installed properly.
This user guide is also available to download in PDF format here.
Package contents:
5x White 15cm Bit Lights
7x Flashing White 15cm Bit Lights
2x Multi Colour Light Strings
2x 6-Port Expansion Board
1x 12-Port Expansion Board
1x 30cm Connecting Cable
1x 15cm Connecting Cables
10x Adhesive Squares
Light My Bricks Power Functions Cable (Power Functions 1.0)or
Light My Bricks Powered Up Cable (Power Functions 2.0)
This light kit is powered using the compatible Power Functions Cable option, which can be connected and powered by your existing power functions battery pack. The lights cannot be powered unless your Winter Holiday Train set is motorised.
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) Start by removing the front sections of the train as per below in order for us to install the front lights.
2.) Remove the trans clear plate and then take a White 15cm Bit Light and place it directly over the stud of the black piece. Reconnect the trans clear plate over the top to secure it in place.
Disassemble pieces of the light section that sits above.
Take another White 15cm Bit Light and thread the connector side through the hole of the black dish piece. Thread the cable all the way through until the LED is right up against the hole as per below.
Reconnect pieces which make up this front light
3.) Reconnect both light sections back to the front of the train starting with the top light and ensure both cables are facing down.
4.) Take a 6-port Expansion Board and connect the two lights to the ports.
Take the 2x Multi Colour Light Strings and connect these to the next available ports on the expansion board
Take a 30cm Connecting Cable and connect one end to the next available port on the expansion board.
Take the Light My Bricks Power Functions Cable or Light My Bricks Powered Up Cable and connect the connector end to the remaining port on the expansion board
5.) Reconnect the front wheels of the train ensuring the cables for the two front lights are neatly laid in between as per below
Using 2x Adhesive Squares, stick the expansion board underneath the train in the below position. Neaten all the cables and secure them underneath the back wheels section.
Thread the Power functions cable (LEGO connector side) up through the inside of the train before mounting the expansion board.
Connect the power functions cable to power pack and turn the power ON test that all lights connected are working OK.
*If you are using the Light My Bricks Powered Up cable (LEGO power functions 2.0), read the below two options on connecting to the Powered Up battery box.
Option 1 – If you’re using the hand controller to control the train motor, Leave the train motor cable connected to port A and connect the Light My Bricks Powered Up cable to port B. This will allow you to turn the lights on if the train is stationary. Press the “+” or “-” button on the controller (on the B side) to test the lights are turning ON and working OK.
Option 2- If you’re using the smartphone app to control the train motor, pull out the train motor cable from the battery box and connect it to the spare socket on the Light My Bricks Compatible Powered Up Cable. If you connect the motor cable to socket B on the battery box, it will cause potential issues with being able to run the motor.
Launch the Powered Up App on your smart phone and ensure the battery box is paired to the phone. Press the “+” or “-
button on the app to test the lights are turning ON and working OK.
Important Note: If using the smartphone App to control the lights and motor, the lights will only turn on when the train is in “accelerate or reverse mode )+ or -)”. The lights will automatically turn off when the motor is turned off or when “STOP” on the controller/app is pressed. Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.6.) Take the next carriage and then remove the top section as well as the inside section as per below.
7.) Pull the 30cm connecting cable all the way across from the front carriage and neatly lay it in between studs before reconnecting the top section over the top. Try not to leave too much cable slack between the first and second carriage as we need as much cable length as possible in order to reach to the remaining carriages.
Hook the second carriage up and then connect the Power Functions Cable onto the power pack and then neaten cables by tucking them into the inside of the front carriage.
Feed the two Multi Colour Light Strings through and behind the white and gold LEGO pieces on each side of the carriage. Tuck the ends of the light strings into the first carriage.
8.) Take the third carriage and then remove the loose pieces from the front before removing the Christmas tree section.
Turn the carriage over and then remove the technic bar from underneath.
The Christmas tree will be unable to spin with this light kit installed therefore, we need to remove and discard the cog piece from the technic bar to prevent the tree from turning.
9.) Disconnect the top and sides of the Christmas tree then disassemble pieces as per below
Take a Flashing White 15cm Bit Light and thread the connector side through the top of the green dish. Thread the cable all the way through and then bend the LED on a 90 degree angle so that the LED is facing up.. Place the top section over the LED and then push down and connect it to secure it in place.
Reconnect the top section to the structure of the Christmas tree ensuring the cable is laid in between studs as per below.
10.) Disconnect the trans coloured round plates from all four sides of the tree.
Remove the top plate from the first side (as per below) and then take a Flashing White 15cm Bit Light and place it directly over the top stud (with cable facing down). Secure the LED in place by reconnecting the trans blue round plate over the top followed by top plate we removed earlier ensuring the cable is laid in on the outside of the studs.
Take another Flashing White 15cm Bit Light and place it directly over the bottom right stud. Secure it in place by reconnecting the trans red round plate over the top as per below
11.) Take another Flashing White 15cm Bit Light and place it directly over the bottom stud on the next plate. Secure it in place by reconnecting the trans yellow round plate over the top.
12.) Repeat this process to install another 3x Flashing White 15cm Bit Lights over the next 2 sides.
13.) Reconnect each side back to the structure of the tree ensuring the cable from the top light is laid in between pieces as per below
14.) Take all 7 cables and then twist them around each other at the base of the tree so that they all come together forming one larger cable.
15.) Re-insert the technic bar we removed earlier underneath the carriage and then reconnect the tree on top of the carriage ensuring the cable is facing toward the back.
16.) Turn the carriage over again and then slightly remove the left side of the wheel section. Locate the other end of the 30cm connecting cable from the front carriage and then pull it across and thread it through the middle of the carriage. Pull it all the way out from the other side and then reconnect the wheel section back to the carriage to secure the cable in place. Before doing so, ensure the cable is laid in between studs.
17.) Take a 12-port Expansion Board and connect the 30cm connecting cable to the first port (from the right) then connect all the cables from the Christmas tree to the other spare ports.
18.) Take a 15cm Connecting Cable and connect it to the next available port along the expansion board then mount the expansion board underneath the carriage in the below position using 4x Adhesive Squares. Neatly tuck in all the cables by pushing them up to prevent them from hanging down and dragging along the tracks. Turn the carriage back over and connect it to the second carriage.
Use your controller or remote app to press ‘accelerate’ to test all the lights installed so far are working OK.
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.19.) Take the last carriage and remove the roof as well as side window sections as per below
20.) Remove the lamp and then disassemble it as per below
Take a White 15cm Bit Light and place it directly over the blue stud. Reconnect the top section of the lamp to secure it in place and then reconnect the lamp to the inside of the carriage as well as the side window sections.
21.) Remove the two lamps from the roof and then disassemble pieces as per below
Take a White 15cm Bit light and then place it (Facing down) directly over the trans clear round brick. Ensure the Bit Light is facing down before reconnecting the top plate with clip on top to secure it in place.
Repeat this step to install another White 15cm Bit Light to the other roof lamp ensuring the bit light is facing down over the trans clear round brick.
22.) Thread the cable for each light through the top of the roof in between gold bar and side of the roof. Pull the cable all the way down from underneath before reconnecting the lamp back in place to each side.
23.) Reconnect the roof to the carriage then pull each roof lamp cable down behind the gold bars and then thread them back through to the outside as per below
24.) Turn the carriage over and then connect the lamp cable from the inside of the carriage to one of the middle ports of the 6-port Expansion Board.
Wind the cable around the expansion board a few times to eliminate excess cable. When the board is roughly at the same length of the remaining two cables, connect them to the expansion board.
Reconnect the white LEGO pieces ensuring the cables from the lights are laid neatly behind.
25.) Take the 15cm Connecting cable from the carriage in front and connect this to a spare port on the 6-port expansion board.
Use 2x Adhesive Squares to mount the expansion board underneath the back carriage in the below position
Turn the carriage over and then connect it to the rest of the train.
26.) Follow the below images to thread the remaining length of the two multi colour light strings along each side of the carriage.
Loop each light string behind the gold bars on the back carriage and then pull each string to the back before threading them back through to the front of the carriage. Thread and secure each light string around sections of the carriage as you see fit.
Use your controller or remote app to press ‘accelerate’ to test all the lights installed so far are working OK.
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
This finally completes installation of the Light My Bricks Winter Holiday Train Light Kit.
We thank you for purchasing this product and hope you ENJOY!
For all questions or issues please follow the troubleshooting guide or contact our customer support team at info@lightmybricks.com
Here is the instructions document for the LEGO London Double Decker LED lighting kit. Please read and follow the steps carefully to ensure this lighting kit is installed properly.
This user guide is also available to download in PDF formathere.
Package contents:
10x White 30cm Bit Lights
2x White 15cm Bit Lights
4x White Strip Lights
1x 6-Port Expansion Board
1x 12-Port Expansion Board
1x 30cm Connecting Cable
4x 15cm Connecting Cables
2x Adhesive Squares
1x USB Power Cable
USB Power Cable has replaced Flat & Round Battery Packs (CR2032) as of June 2022 due to child safety regulations. Please use the USB Power Cable in place of the Battery Pack.
Assorted Bricks:
4x Plate 1×6 (for mounting strip lights)
4x Plate 1×1 (trans red)
2x Plate 1×1 (trans orange)
1x Round Plate 1×1 (trans clear)
1x Plate 2×4 (black)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) Start by removing the top level of the bus, then remove the following the pieces above the engine so that we can install the first light.
2.) Remove and discard the trans clear tile then take a White 30cm Bit Light and thread the connector side through the front hole of the 1×1 red brick.
Thread the cable all the way through until the Bit Light is right up against the front of the brick. Secure the Bit Light in place by connecting the provided LEGO 1×1 trans clear round plate over the top.
3.) Lift up the engine bonnet and then take the connector side of the Bit Light cable we just installed and thread it through the space which leads underneath and outside the back of the left wheel. Pull the cable all the way out from underneath the bus and then reconnect the brick with bit light installed followed by the piece on the left of it as well as the window section.
4.) We will now install the two head lights. First disconnect the whole front section by using your finger to lift it out from underneath the front of the bus.
Disassemble pieces as per below
5.) Take a White 30cm Bit Light and then place it directly over the stud of one of the white 1×1 plates. Secure the light in place by reconnecting the light grey round piece over the top, followed by the trans clear piece, then reconnect this head light to the front section. Ensure the cable is facing outward.
Repeat this step to install another White 30cm Bit Light to the other headlight
Tuck both cables behind before reconnecting the front section back to the bus.
6.) Remove each of the front wheels before bringing each cable behind and toward the back of the bus.
7.) Flip the bus over and take the 3 Bit Light cables and thread them through the centre hole of the light grey brick underneath.
Disconnect the Black 2×8 plate and then thread the 3 cables through the hole of the next light grey brick.
Reconnect the black 2×8 plate.
8.) Take the 12-Port Expansion board and then connect the 3 Bit Light cables to the first available ports.
Take this time to test the lights we have installed so far. To do so, take the Flat Battery pack and insert 2x CR2032 batteries to it. Connect the battery pack cable into the expansion board, turn on and verify all is working OK.
Important Note:USB Power Cable has replaced Flat & Round Battery Packs (CR2032) as of June 2022 due to child safety regulations. Please use the USB Power Cable in place of the Battery Pack.
Once you have verified all is working OK, disconnect the battery pack and tuck the expansion board in underneath as per below
9.) We will now install lights to the back of the bus. Disconnect the following sections and then locate the below provided transparent coloured LEGO plates and have them ready.
Remove and discard the flat trans coloured tiles from the light grey plate as per below.
10.) Take a White 30cm Bit Light and place it directly over the top of the bottom stud of one of the grey plates. Secure it in place by connecting a provided trans red plate.
Repeat this step to install another White 30cm Bit Light over the middle stud except secure it in place using a provided trans orange plate.
Repeat again to install another White 30cm Bit Light over the top stud, this time securing using a provided trans red plate.
Repeat this step to install another 3x White 30cm Bit Lights to the other tail light section using provided trans red and orange plates.
11.) Remove the following sections from the back left of the bus.
12.) Take one of the tail light sections and then reconnect it to the set of red bricks, ensuring the cables are facing the right. Fold the cables over the right side before reconnecting this section back to the back left of the bus as per below.
Remove the top section of the bus and then pull the 3 cables over to the right along the back wall and tuck them in behind the umbrella. Pull the cables all the way to the right and then tuck them in underneath the stairs.
Reconnect the top section we removed earlier.
Bring the 3 cables down underneath by threading through the lower space of the right corner.
13.) Disconnect the following section of bricks from the back of the right side of the bus as per below.
Reconnect the right set of tail lights ensuring the cables are facing toward the left. Fold the cables across the left and then tuck them in behind before reconnecting this section back.
Bring the 3 cables from the right tail lights down underneath by threading through the lower space of the right corner.
14.) Remove the top section of the bus again so that we can install a light underneath.
Take a White 30cm Bit Light and stick it underneath this section in the following position using an adhesive square. Ensure the cable is facing the same way as per below (diagonal top right)
Reconnect the top section.
Pull the cable across toward the back right and then thread it back into the bus and then out the bottom spacing, just like how we threaded the previous 3 cables. Pull the cable all the way down and ensure the cable is laid in between studs above.
15.) Take a 30cm Connecting Cable and then thread it through the inside of the bus and then out through the bottom space.
Pull the top side of the cable above and the secure in place underneath the red tile. Ensure you leave about 8–9cm of excess cable between the plate and the connector.
Pull the cable down all the way down from underneath and then reconnect the corner section we removed earlier.
16.) Lift the back of the bus up and then pull all 8 cables toward the left and then down underneath. Remove the black 2×8 plate as well as the black 1×12 plate.
Spread the cables out so that we can reconnect the black 1×12 plate. We need to spread the cables out in order for them to all lay evenly between the studs of the 1×12 plate.
Using the provided Black 2×4 Plate, secure some of the cables on the right by connecting this plate underneath in the following position. (We will use the 2×8 plate we removed earlier from this section to secure cables later)
17.) Remove the next black 1×12 plate along and then tuck and pull all cables underneath the wheel axle and out the other side.
18.) Connect all 8 cables to the 12-port expansion board.
Connect the Flat Battery Pack to the remaining port of the expansion board and then tuck everything neatly underneath in the following space.
Important Note:USB Power Cable has replaced Flat, Round, and AA Battery Packs as of June 2022 due to child safety regulations. Please use the USB Power Cable in place of the Battery Pack.
If you are using the USB Power Cable, you will be unable to hide the power source. Therefore, run the USB Power Cable out from underneath the bus.
Reconnect the black 1×12 plate we removed earlier over the top to secure cables and battery pack. Take the black 2×8 plate we removed earlier and then connect it to the following position to secure the remaining part of battery pack and cables.
Take this time to verify all the lights we have installed so far are working ok by turning the battery pack ‘ON’.
19.) We will now move onto installing lights to the upper level. First remove the roof followed by the front indicator light sections.
Disassemble the front indicator light sections as per below
20.) Take a White 15cm Bit Light and thread the connector side through the hole on top of the light grey stud. Thread all the way through until the Bit Light is right up against the edge and then secure it in place by reconnecting the trans-orange plate over the top.
Note: We are reconnecting the trans orange plate a different way than the original. Connect the plate on top of the grey plate rather than on the bottom.
Repeat this step to install another White 15cm Bit Light to the other indicator light before reconnecting both to the front of the bus.
21.) Take the 6-port Expansion Board and then connect the two Bit Lights we just installed to the spare ports.
22.) Take 2x White Strip Lights and stick them to the bases of 2x provided LEGO 1×6 Plates.
Take a 15cm Connecting cable and connect it in between each Strip Light. Take another 15cm Connecting cable and connect it to the other end of one of the Strip Lights.
Connect the other end of this 15cm cable to the 6-port expansion board.
23.) Lift the upper level and turn it over so we can access underneath. Connect the 2x Strip Lights to the following positions.
Take another 15cm Connecting Cable and connect it to a spare port on the 6-port Expansion Board.
24.) Remove the following section from the front of the bus.
Take the 6-port expansion board and wind the bit light cables around the board to eliminate excess cables.
Take the other end of the 15cm cable we connected in previous step and thread it through the space which leads to the inside of the upper level. Pull the cable up from underneath.
Thread the expansion board up the same space.
25.) To eliminate excess cable from the 15cm cable between the strip light and expansion board, first remove the next plate underneath and then reconnect over the top as per below
You can also eliminate excess cable by looping them underneath the LEGO plates as per below.
26.) Tuck the cables from the indicator lights in between sections by disconnecting, laying cables behind, and reconnecting
Once all cables are neatly tucked in and hidden, reconnect the front base section we removed earlier
27.) Remove the front roof section as well as the front seat. Tuck the expansion board in below before reconnecting the front seat.
28.) We will now lay the spare 15cm cable up the corner of the window. First remove the following sections before laying the cable underneath in between studs, and reconnecting sections.
Reconnect the front roof section ensuring the 15cm cable is still accessible.
29.) Take the remaining two White Strip Lights and stick them to the bases of two provided LEGO 1×6 Plates. Take the remaining 15cm Connecting Cable and connect it to one of the Strip Lights.
Mount the Strip Light with cable connected to the roof of the Bus in the following position. Thread the other end of the cable across and underneath the grey plates to then connect to the other White Strip Light.
Mount the remaining Strip Light as per below
Remove the black 2×8 plate to allow you to connect the other end of the 15cm cable from the level below to the Strip Light.
Reconnect the Roof of the bus to original prosition.
30.) Take the entire upper level over the bottom level of the bus and then locate the other end of the spare 30cm cable near the stair case. Connect this into the Strip Light closest to it before securely reconnecting the upper level to bottom level.
This finally completes installation of the London Double Decker Bus Lighting Kit. You can now turn your on your battery pack by accessing the switch from underneath the Bus. Turn “ON” and ENJOY!
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Destiny’s Bounty (70618) LED light kit , please click here to view the product page
Package contents:
11x White 30cm Bit Lights
3x White Strip Lights
1x 6-Port Expansion Board
1x 12-Port Expansion Board
1x 30cm Connecting Cable
2x 15cm Connecting Cables
1x 5cm Connecting Cable
1x AA Battery Pack (requires 3x AA batteries)
2x Adhesive Squares
LEGO Pieces:
2x Plate 1×6 (for mounting strip lights)
6x Round Plate 1×1 (trans red)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) First remove the base of the top floor as per below images.
2.) We will first install lights to those attached to the front mast and along the middle. Remove the front light section and then disassemble pieces as per below:
3.) Install a White 30cm Bit Light by threading the connector side through the base of the trans yellow brick (larger hole). Thread the cable all the way through until the Bit Light is sitting inside the brick.
Thread the cable through the base of the black lamp shade piece as well as the gold round plate with hole before connecting pieces together.
Reconnect the black hook piece by carefully pushing down through the top of the lamp shade piece. NOTE: You will notice that this particular piece will not push all the way down. Do not force push it all the way.
It should look similar to the below example.
Lastly, reconnect the remaining piece which sits underneath the lamp before reconnecting back to the front mast.
4.) Next, we will install lights to the lanterns along the middle line. Disconnect the one closest to the front lamp we just installed and then remove the gold piece underneath.
Take another White 30cm Bit Light and then place the bit light directly over the top of the gold piece we removed. Secure the light in place by reconnecting the trans red piece over the top as per below.
5.) Take the cable from the bit light and then pull it up and then across the top and lay in between the black clip.
Reconnect this section back to the middle line ensuring the cable is facing forward.
The cable should be laid in between the clip handles.
6.) Twist the cables from the two lights we just installed around each other so they come together forming one cable.
Take the cable and then wind the cable around the mast and then pull the cable toward the right to then thread underneath the chain leading to the bottom deck.
Use your LEGO removal tool to remove the 4×4 plate cream coloured. Lay the cable down in between studs underneath before reconnecting the plate back over the top.
7.) We will now install lights to the second and third lanterns along the middle line. Remove these two sections and then disconnect the gold pieces from the bottom of them.
Following the same method we used for the first lantern, install another 2x White 30cm Bit Lights to these two lanterns.
Take the cable from the bit light and then pull it up and then across the top and lay in between the black clip for both lanterns.
8.) Reconnect both lanterns back to the middle line ensuring both cables are facing the back.
The cable should be laid in between the clip handles.
9.) Twist the two cables together to form one larger cable and then follow the below images to wind the cable around the mast and then pull toward the inside of the bottom deck.
Secure this cable by laying it underneath the table with the mug on it ensuring the cable is laid neatly in between studs underneath.
10.) We will now install lights to the lanterns on the sides of the boat (2 each side). First remove the first section at the base of it’s pole and then locate one of the provided Trans Red Round Plates.
Take a White 30cm Bit Light and place it directly over the top of the trans red round plate. Secure the light in pace by connecting this piece up inside the trans red lantern piece ensuring the cable is facing toward the pole as per below.
Wind the cable around the pole and then reconnect this section to the side of the boat.
Repeat this process to install a light to the other lantern using another White 30cm Bit Light and provided Trans Red Round Plate.
11.) Lay the cable from this lantern we just installed underneath the brown LEGO tile pieces ensuring the cable is laid in between studs underneath as per below
12.) Turn the ship around to install lights to the other 2 lanterns on the other side using another 2x White 30cm Bit Lights and 2x Provided Trans Red Round Plates.
Lay the cable for the left lantern underneath the two brown LEGO tile pieces as per below:
13.) Secure the cables for the other two lanterns underneath the black 1×8 tile by first disconnecting, laying the cable in between studs, and then reconnecting it (over the studs closest to the wall as per below)
14.) Take a 12-port Expansion Board and then connect all eight lights to the available ports.
Take this time to test all lights are working ok by taking the the AA Battery Pack and inserting 3x AA batteries into it. Take the battery pack cable and connect it to one of the available ports on the expansion board. Turn the switch ON and verify that all lights are working OK.
Once you have verified that all lights are working OK, remove the battery pack cable and then proceed to the next step.
15.) Take a 30cm Connecting Cable and connect it to a spare port on the 12-port expansion board.
Tuck the expansion board and cables down underneath the lower deck and then pull the 30cm connecting cable out and then secure underneath the brown tile pieces (same ones we used to secure the lantern cable)
16.) Ensure all cables are well tucked in before reconnecting the section we removed at the very start.
Ensure you do not force this plate to reconnect as it may damage the bit light cables.
17.) Remove the top level of the ship as per below:
We will now thread and hide the 30cm cable through to the upper level. First remove the following tiles as well as the ladder.
Pull the cable up and then lay it across the top of the upper level in between studs. Reconnect the ladder piece over the top, followed by the tiles we removed earlier.
18.) We will now install a light to the lantern on the front of the upper level. Disconnect this section and then remove the gold piece from underneath the lantern.
19.) Take a White 30cm Bit Light and then place it over the top of the gold piece. Reconnect the lantern piece over the top securing it in place.
Wind the cable around the top of the pole and then pull it toward the back.
Remove the steering wheel section and then reconnect to it the lantern piece we just installed a light to.
Lay the cable underneath and towards the inside of the upper deck before reconnecting this section.
20.) Turn the upper level toward the back so that we can install lights to the lanterns on the back of the boat.
Remove one of the back lanterns at the following section and then install another White 30cm Bit Light using a provided Trans Red Round Plate (same method as we used for lanterns on the side)
21.) Reconnect this lantern section back to the ship and then remove the black rounded tile. Use the LEGO removal tool to create a gap so that we can thread the cable inside.
Close up the gap and then reconnect pieces we removed earlier.
22.) Repeat previous step to install another White 30cm Bit Light to the other back lantern using another Trans Red Round Plate.
22.) Reconnect the lantern section and then remove the black round tile piece. Use the LEGO removal tool to create another gap to allow you to thread the cable inside.
Close up the gap and then reconnect pieces we removed earlier.
23.) Take a White Strip Light and connect a 15cm Connecting Cable to the left port.
Using the adhesive backing, stick the strip light underneath the roof of the upper deck in the following position. The Strip Light should be placed in the middle between the two front roof flaps.
24.) Take all the cables from the upper level and then thread them down the bars which lead to the lower level. Lift the whole section up and then pull the cables down from underneath.
25.) Take a 6-port Expansion Board and then connect all four cables to the available ports.
26.) Take 2x White Strip Lights and then stick them (using their adhesive backing) onto the base of the 2x provided LEGO 1×6 Plates.
Take a 15cm Connecting Cable and then connect them in between the strip lights.
Take a 5cm Connecting Cable and connect it to one of the strip light ports and then connect the other end into the 6-port expansion board.
27.) Connect both strip lights underneath the upper level section in the below positions. Ensure the strip light with the spare port is closest to the back of the ship.
Hide the 15cm cable underneath the grey 2×8 plate as per below.
28.) Use the provided double sided adhesive squares to mount the expansion board to the following position.
29.) Pull all the excess cables down and twist them together before tucking them inside underneath the grey 2×8 plate.
30.) Bring the entire upper level over the ship and then locate the other end of the 30cm connecting cable from below and connect it to the spare port on the 6-port expansion board.
31.) Before reconnecting the upper level, take the AA Battery Pack and place it behind. Connect the battery pack cable into the strip light towards the back.
You can now securely reconnect the upper level.
For easy mobility, the battery pack can be fitted nicely in the back in between the upper and lower levels. Just ensure you fold down the telescope before doing so.
This finally completes installation of the Destiny’s Bounty Lighting Kit. Now turn the battery pack on and ENJOY!
Here is the instructions document for the LEGO High-Speed Passenger Train LED lighting kit. Please read and follow the steps carefully to ensure this lighting kit is installed properly.
2x Flat Battery Packs (requires 2x CR2032 batteries each battery pack = total 4x batteries)
4x Adhesive Squares
LEGO Pieces:
4x Plate 1×6 (for mounting strip lights)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Installing Lights to the Train
1.) We will start with installing lights to the front of the passenger train. First remove the front section as well as the following sections from the front carriage.
2.) We will be replacing the original power functions lights with our much brighter Bit Lights. Remove the power functions lights as per below.
3.) Take one of the White 15cm Bit Lights and then thread it through one of the the holes for one side of the headlight.
Bend the Bit Light on a slight angle so that it is shining straight ahead and then secure the light cable in place by connecting the cable under the red 1×2 plate as per below. Ensure that the cable is laid in between studs and facing the inside of the train before reconnecting the plate.
4.) Repeat the previous step to install another White 15cm Bit Light for the other headlight.
5.) Take a 6-Port Expansion Board and then connect the two Bit Light cables we just installed to the available ports.
6.) Take a 15cm Connecting Cable and connect one side to one of the available ports on the expansion board.
7.) Take a Flat Battery Packs and insert 2x CR2032 batteries into it. Connect the battery cable to the expansion board.
Turn the battery pack ‘ON’ to test the lights are working OK.
8.) Take the other end of the 15cm Connecting Cable and then bring it underneath the remote sensor.
Tuck the expansion board and excess cables underneath the remote sensor
9.) Secure cables underneath the grey and blue LEGO pieces ensuring the cables are laid neatly in between studs
Position the battery pack neatly behind the driver and then reconnect the front section of the train.
10.) Take a White Strip Light and then stick it onto one of the provided LEGO 1×6 Plates using it’s adhesive backing.
Connect the other end of the 15cm connecting cable from the front to the left port and then take a 30cm Connecting Cable and connect it to the right port.
11.) Take the roof sections we disconnected earlier and place them together and turn them upside down. Mount the Strip Light underneath in the following position.
Before we reconnect the roof, remove the following section.
12.) Remove the following section from the back of this carriage and then bring the cable across to the next carriage. Reconnect the section over the cable ensuring the cable is laid in between studs.
Reconnect the power button section we removed earlier.
13.) Remove the roof off of the next carriage followed by the front and back sections on the top.
14.) Take another White Strip Light and stick it to the base of another provided LEGO 1×6 Plate. Connect the other end of the 30cm Connecting Cable from the front carriage to the left port of the strip light and then take a 15cm Connecting Cable and connect it to the right port.
15.) Mount the strip light underneath the carriage roof in the following position.
Neaten the 30cm cable between the front and middle carriage as per below, before reconnecting the roof and top front section.
16.) Pull the other end of the 15cm Connecting Cable across to the back carriage before reconnecting the pieces on top of the back of the middle carriage.
17.) Remove the roof off the back carriage as well as the front pieces on top.
18.) Take another White Strip Light and stick it to the base of another provided LEGO 1×6 Plate. Connect the other end of the 15cm connecting cable from the middle carriage to the left port of the strip light.
Mount the strip light underneath the roof in the following position.
19.) Take the remaining White Strip Light and stick it to another provided LEGO 1×6 Plate. Take a 5cm Connecting Cable and connect it to the right port.
Connect the other end of the 5cm connecting cable to the left port on the other Strip Light we already mounted.
Mount the last strip light in the following position.
20.) Remove the back of the carriage as pictured below and then take a 5cm Connecting Cable and connect it to the spare port on the end Strip Light. Connect the other end of the cable to a 6-Port Expansion Board.
21.) Reconnect the top middle section of the roof and ensure you leave enough cable length in between carriages for the carriages to be able to turn on the railway tracks.
22.) Take 2x White 15cm Bit Lights and connect them to the expansion board. Thread the other end of the Bit Lights through the holes of the light grey technic pieces for the tail lights. Bend both ends of the Bit Lights on an angle so they are facing forward.
23.) Secure each light underneath the following LEGO pieces ensuring the cables are laid in between studs.
24.) Use 2x adhesive squares to mount the expansion board to the inside of the carriage as per below:
25.) Reconnect remaining sections of the roof and back piece.
This completes installation of the lights for the Train. Turn the battery pack on to test all is working ok before moving onto installing lights to the train station.
Installing Lights to the Train Station
1.) Remove the front crossing light and then disconnect the trans red round plate.
2.) Take a Flashing White 30cm Bit Light and then place it directly over the white stud underneath with the cable facing down. Secure the light in place by reconnecting the trans red round plate over the top.
Wind the bit light cable around the pole 2–3 times as per below
3.) Reconnect the light back to the track and then lay the cable underneath the tracks toward the train stop.
4.) Remove the other crossing light and then disconnect the trans red round plate.
Take another Flashing White 30cm Bit Light and install it using the same method as we did for the other crossing light.
5.) Wind the bit light cable around the pole 2–3 times as per below and then reconnect the crossing light to the track and thread the cable underneath the track plate toward the train stop.
6.) Turn the set around the back side and take the 6-Port Expansion board and connect the 2 lights to the ports.
7.) Disconnect the white piece from the top of the train stop sign.
8.) Take a White 15cm Bit Light and then place it facing down on top of the second stud from the left of the trans clear train stop sign (so that it shines down).
Secure the light in place by reconnecting the white piece on top.
9.) Thread the cable back underneath the trans clear train stop sign facing toward the back and then connect it to the 6-port expansion board as per below.
10.) Disassemble the base and pieces of the train stop as per below and then carefully lay the three cables in between studs before reconnecting pieces over the top to secure them in place.
11.) Take the Flat Battery Pack and insert 2x CR2032 Batteries to it then connect the battery pack cable to the expansion board.
12.) Use the provided adhesive squares to mount the expansion board underneath the base section of the train stop before reconnecting it to the st as per below
13.) Tuck the battery pack neatly underneath the train stop base and then setup your train track as desired.
This completes installation of the lighting kit for the LEGO Passenger Train and Train stop. Now turn both train and train stop lights on via their battery packs and ENJOY!
Here is the instructions document for the LEGO Sydney Opera House LED lighting kit. Please read and follow the steps carefully to ensure this lighting kit is installed properly.
If you wish to download this instructions guide in PDF format you can do so by clicking here
30x White 30cm Bit Lights (28 required, includes 1-2 extra)
4x Multi-Coloured Strip Lights
3x 12-Port Expansion Boards
1x 6-Port Expansion Board
7x 30cm Connecting Cables
1x 30cm USB Cable
LEGO Pieces:
2x Plate 1×6, Black
4x Plate 2×6, Black
4x Plate, Modified 1×2 with handle on End — Close Ends, Black
4x Tile, Modified 1×1 with Clip, Black
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Instructions for installing this kit
1.) In order for us to install lights to all of the lamp posts, we will need to remove several sections from the top of the base. This will also allow us to wire all the lighting and hide cables underneath. With the opera house positioned as per below, follow the images in order to remove sections.
Your opera house should look similar to below
2.) Turn your set around so that you are facing the front and then remove the 12x pictured lamp posts.
Disconnect the trans-clear round plates from all of the lamp posts
3.) Take a White 30cm Bit Light and place it directly over the top of one of the lamp posts. Secure the light in place by reconnecting a trans-clear round plate over the top.
Push the cable down so that it is facing directly down.
Repeat this step to install another 11x White 30cm Bit Lights to the remaining 11 lamp posts.
4.) Reconnect three of the wired lamp posts to the right side of the set. Ensure the cables are facing the outside as per below
5.) Starting with the top lamp posts, hide the lamp post cable underneath the following tile next to it. Ensure the cable is laid in between studs before reconnecting the tile over the top.
Remove the entire plate the lamp post is connected to and then bring the cable underneath before reconnecting the plate.
Repeat this step for the other 2 wired lamp posts.
6.) Reconnect the remaining 9 wired lamp posts to the set, ensuring the cables are facing toward the outside.
7.) Starting with the next 2 lamp posts on the right, loop them underneath the plates below. Note: for these 2, we do not need to lay the cable underneath the tiles on the outside before doing so. We do however require to remove extra plates in order to lay the cable all the way underneath to allow us to later connect them to an expansion board.
8.) To allow us to lay the remaining lamp post cables, remove the following sections.
9.) The cable for the next lamp post on the right also does not require to be laid underneath the tile in front. Simply lift the plate it is connected to and lay the cable underneath as per below
10.) For the next 2 lamp posts cables along, lay them underneath tiles before looping/laying them underneath the plates they are connected to.
11.) For the next 2 lamp post cables, simply lay them underneath plates.
12.) Lay the remaining 2 lamp post cables underneath tiles before laying them underneath the plates they are connected to.
Your set should now look similar to the below:
13.) Take the following LEGO Pieces that were provided in this light kit. These will make up one of the spot lights we are installing to each side.
Assemble them as per below and then take a Multi-Coloured Strip Light and stick it to the base of the 2×6 plate using the adhesive backing.
14.) Take a 30cm Connecting Cable and connect it to the port on the strip light and then connect the spot light to the following position on the set. Ensure the spot light is facing the correct way and then angle it up as per below:
15.) Take the connecting cable from the strip light and then loop it around the base of the spot light and then pull it up around as per below
16.) Take the following 2 lamp post cables from the right side and then lay them underneath the following plate by disconnecting and reconnecting it over the cables.
17.) Take a 12-port Expansion Board and then take 2x 30cm Connecting Cables and connect one to each port on the far sides.
Take all the lamp post cables laid on the left side of the set as well as the 30cm cable from the spot light (there should be 10 in total) and connect them to the 12-port expansion board.
18.) Take the other end of the 30cm connecting cable closest to the top of the expansion board and thread it underneath the following section and then connect it to another 12-port Expansion Board.
Connect the remaining 3 lamp post cables on the right side of the set to the next available ports on the expansion board.
19.) Neaten up all the cables on the left side by gathering them together and tucking them in before reconnecting the plates and sections we removed earlier. Before reconnecting them, ensure the cables are laid in between studs. Do not forcefully reconnect the plates over the top of cables.
Take this time to test all the lights we have installed so far and to ensure everything is properly connected. To do so, take the 30cm USB Cable and connect it to a spare port on the 12-port expansion board on the right side. Connect the USB plug to your USB power bank and ensure all lights are working OK.
Once you have verified all the lights are working OK, disconnect the USB cable and power bank and proceed to the next step.
20.) Turn the set around to the right side (as per below)and then remove the following sections by following the example images.
place hand underneath the above section and then carefully remove
21.) Remove the remaining 8 lamp posts from this side of the set and then remove the trans-clear round plates from them
Following the same method we used for previous lamp posts, install another 8x White 30cm Bit Lights to these lamp posts.
22.) Reconnect the 8 wired lamp posts to the set ensuring the cables are facing toward the outside.
23.) Take the first four lamp posts on the left and then lay each cable underneath the tiles directly in front of them.
Remove the plates under the first three lamp posts and then tuck the cables underneath before reconnecting the plates.
24.) Remove the following tile between the third and fourth lamp posts we just secured cabling for.
Using the following provided LEGO pieces, assemble them together to make another spot light this time, connected to the 1×6 plate.
25.) Take another Multi-Coloured Strip Light and stick it to the base of the 2×6 plate.
Take a 30cm Connecting Cable and connect it to the port on the strip light. Connect the spot light to the following position on the set.
Loop the cable behind and then pull the cable in towards the set as per below.
26.) Continue to secure the cables for the next two lamp posts along the sides as well as the spot light cable by laying them underneath tiles and then laying them underneath the plates below.
Reconnect the spot light base (1×6 plate) as per below and then set the angle of the spot light so that it is pointing up toward the left (eventually at the opera house)
27.) Remove the following plate to allow us to then lay the cables for the remaining three lamp posts.
28.) Take the first six cables we laid on the left and then connect them to the 12-port expansion board we used in step 18.
Take another 30cm connecting cable and connect it to one of the remaining ports on the expansion board.
Connect the other end of the 30cm connecting cable to a 6-Port Expansion Board
29.) Take the remaining three lamp post cables on the right and connect them to the 6-port expansion board. Reconnect the grey plate we removed earlier.
Take this time to test all the lights we have installed so far and to ensure everything is properly connected. To do so, take the 30cm USB Cable and connect it to a spare port on the 6-port expansion board. Connect the other end to your USB power bank and ensure all lights are working OK.
Once you have verified all the lights are working OK, disconnect the USB cable and proceed to the next step.
30.) Tuck in the cables from the 6-port expansion board underneath and then reconnect sections above which we removed earlier.
31.) Turn the set around so we are facing the opposite side and then remove the eight lamp posts we are yet to install lights for. Disconnect the trans-clear round plates from them.
32.) Install the remaining 8x White 30cm Bit Lights to the lamp posts and then reconnect them to the set ensuring the cables are facing toward the outside.
33.) Lay the cables for the five lamp posts toward the right underneath the tiles directly in front of them.
Remove the following sections.
34.) First lay the lamp post cable on the right underneath the plate it is connected to, then lay the lamp post cable on the left underneath it’s plate before reconnecting it. Ensure you carefully lay the cables in between studs underneath.
35.) Remove the following tile in between the two lamp posts we just connected as this is where we will be installing another spot light.
Locate the following provided LEGO pieces and assemble them as below to make another spot light.
36.) Stick another Multi-Coloured Strip Light to the base of the 2×6 plate and then connect a 30cm Connecting Cable to the port.
Reconnect the spot light to the following position
Loop the 30cm connecting cable around the spot light and then pull toward the inside of the set as per below.
Disconnect the plate underneath again and then lay the spot light cable underneath before reconnecting the plate.
37.) Move on to the next lamp post toward the left and lay cable for the lamp post underneath the plate before reconnecting.
38.) Locate the other end of the 30cm Connecting Cable we connected to the very first 12-port Expansion board we used and then connect it to the last remaining 12-port Expansion Board.
Connect the three lamp cables we have secured down, as well as the spot light cable to the expansion board.
Take this time to test all the lights we have installed so far and to ensure everything is properly connected. To do so, take the 30cm USB Cable and connect it to a spare port on the 12-port expansion board. Connect the other end to your USB power bank and ensure all lights are working OK.
Once you have verified all the lights so far are working OK, disconnect the USB cable and proceed to the next step.
39.) We will now move onto connecting the rest of the lamp posts as well as the final spot light. In order to do so, we will need to remove sections to lay the cables underneath. Follow the below example images to remove sections.
40.) Take the 12-port Expansion Board closest to you and then bring it across to the left by threading underneath the following section.
41.) Locate the remaining provided LEGO pieces and then assemble them as per below to make up a spot light
Stick another Multi-Coloured Strip Light to the base of the 2×6 plate and then connect a 30cm connecting cable to the port.
42.) Connect the spot light to the following position facing the Opera House.
Loop the cable behind the spot light and then pull towards the inside. Thread the cable underneath the following section and then connect it to a spare port on the 12-port expansion board
Carefully reconnect the 6×8 plate we removed earlier. The cable should fit nicely between plates. Take caution and ensure you do not forcefully connect the plate and snap the cable.
43.) Start with the two lamp posts on the far left. Disconnect the plate and then lay cables underneath and ensure the cables underneath are laid in between studs before reconnecting the plate.
Connect the cables for these two lamp posts to the 12-port Expansion Board.
44.) Secure cable for the next two lamp posts along by first disconnecting the plate and then laying the cables underneath before reconnecting the plate. Ensure the two cables are neatly laid and coming out underneath.
Connect the two lamp post cables to the expansion board.
45.) Take the USB Cable and connect it to the expansion board. Lay the cable down with USB plug facing outside. This will be where the USB power Bank will sit.
Reconnect the remaining lamp post section ensuring you lay the cable underneath the plate. Ensure you also have plenty of length for the USB Cable.
Connect the remaining lamp post cable to the last port on the expansion board.
46.) Tuck all the cables and expansion board underneath sections as neatly as you can ensuring there no loose wires.
Before we start reconnecting all the sections we removed, take this time to test all the lights we have installed so far and to ensure everything is properly connected. Connect the USB Cable to your USB power bank and ensure all lights are working OK.
47.) We can now start reconnecting all the sections we removed earlier. Follow the below images to reconnect sections in order.
This finally completes installation of your LEGO Sydney Opera House Lighting Kit. You can now position your USB power Bank behind, connect the USB Power Bank, and ENJOY!
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Package contents:
5x White 30cm Bit Lights
4x Flashing White 30cm Bit Lights
4x White Strip Lights
3x 6-Port Expansion Boards
1x Multi-Effects Board
2x 5cm Connecting Cables
5x 15cm Connecting Cables
1x USB Power Cable
LEGO Pieces:
1x TransBlue RoundPlate 1×1
4x Trans Red Saber Bar 4L
4x Plate 1×2 (black or grey)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Instructions for installing this kit
1.) We will first install lights to the upper cannons. Start with one of the upper cannons and disconnect the top section and then disassemble pieces as per below
2.) Take one of the provided LEGO trans red saber bars and replace the light grey bar from this set.
Take a White 30cm Flashing Bit Light and then bend the tip of it up in a 90 degree angle as shown below
Place the Bit Light (face down) into the inside of the bottom of the cannon section. Place it as far down inside as you can
Carefully reconnect this section back to the cannon pole.
3.) Pull the Bit Light cable toward the back and then loop it around toward the inside of the pole. Secure the cable in place by using one of the provided LEGO 1×2 Plates to mount up underneath the wing as per below.
Ensure the cable is laid in between the lego studs.
4.) Take a White Strip Light and then connect the Bit Light cable into one of the ports, then take a 15cm Connecting Cable and connect it to the other port.
5.) Peel off the adhesive backing from the Strip Light and then stick it underneath the wing in the following position.
Thread the other end of the 15cm connecting cable up through the space which leads to the top side of the wing. Pull the cable up from the other side.
6.) Remove the following sections of the top of the X-Wing to allow us to lay the cable underneath.
Reconnect pieces over the top of the cable ensuring it is first laid neatly in between studs.
7.) Take a 6-Port Expansion Board and connect the 15cm cable into one of the ports.
8.) Turn the X-Wing around and repeat steps 1–5 to install another Flashing White 30cm Bit Light, White Strip Light, and 15cm Connecting Cable to the upper wing on the other side of the space ship.
9.) Thread the other end of the 15cm Connecting cable up through the following spacing which leads to the other side. Pull the cable up from the other side.
Remove the following pieces around the top of the X-Wing and then pull the cable over and lay in between studs. Reconnect pieces over the top.
10.) Connect the cable from this side into a spare port on the expansion board.
11.) Remove the following sections of the cockpit to allow us to then remove the joystick section. Disassemble pieces as per below.
12.) Take a White 30cm Bit Light and place it directly over the stud of black plate. Secure the Bit Light in place by connecting the provided LEGO Trans Blue 1×1 Plate over the top.
Reconnect this plate (this time with the trans blue plate facing up) back to the joystick and then reconnect back to the cockpit.
13.) Remove the following sections (including R2D2) to allow us to pull the Bit Light cable toward the back.
Carefully lay the cable in between studs and then reconnect pieces we removed over the top.
Reconnect remaining sections of the cockpit
14.) Take the Bit Light cable from the cockpit and then connect it to the next available port on the 6-port expansion board.
Take this time to test the lights we have installed so far. To do so, take the AA Battery Pack and insert 3x AA batteries into it. Take the battery pack cable and connect it to the expansion board. Turn the battery pack ‘on’ and verify all is working OK.
If you’re using the USB Power Cable, connect this to the board this instead of the battery pack, and connect the other end to a USB Power Bank or wall adaptor (sold separately) and turn it ON to test the lights are working OK.
Once you have confirmed all is working OK, disconnect the battery pack /usb cable from the expansion board and move on to the next step.
15.) Turn the X-Wing over so that you can access underneath and then remove the following sections.
16.) Turn the X-Wing back over and then take a new 15cm Connecting Cable and connect it to a spare port on the 6-port expansion board.
Thread the other end of this cable down through the spacing and then turn the X-Wing over to then pull the cable out from above.
17.) Take another 6-Port Expansion Board and then connect the other end of the 15cm connecting cable we pulled down into one of the available ports.
Turn the X-Wing back over again and then neaten up all the cables by tucking them as well as the expansion board in through the space. Reconnect R2D2 and the remaining sections we removed previously.
18.) We will now proceed to lighting the bottom cannons and wings on each side starting with the left section. Follow the same methods we used for the upper cannons to install another White Flashing 30cm Bit Light as well as provided Trans Red Saber Bar.
19.) Pull the cable back and then loop once around the cannon pole. Turn the X-Wing over and then secure the Bit Light cable in place by using a provided LEGO 1×2 plate to connect over it.
20.) Take a White Strip Light and then connect the bit light cable into one of the ports. Take a 15cm Connecting Cable and connect it to the other port on the Strip Light.
Stick the White Strip Light down in the following position underneath the bottom left wing using the adhesive backing.
21.) Take the other end of the 15cm cable from the strip light and then loop it under the White 2×12 LEGO plates. Pull it out from underneath and then connect it to the next available port on the 6-port expansion board.
22.) Repeat previous steps to install another Flashing White 30cm Bit Light, Trans Red Saber Bar, White Strip Light and 15cm Connecting Cable to the right cannon and wing.
If you find that you have excess cable from the bit lights, you can secure them down to prevent them from dangling by reconnecting LEGO tiles over them. Just ensure the cable is laid in between studs.
23.) Take the other end of the 15cm connecting cable from the strip light and then connect it to the next available port on the 6-port expansion board.
Reconnect the 2×12 LEGO plates we removed in step 15.
Take this time to test the lights we installed to the bottom wings and cannons by connecting the battery pack cable /usb cable into one of the spare ports on the expansion board. Turn the battery pack ‘on’ and verify all is working OK
24.) We will now move onto lighting the back jets. First disconnect the top left jet section and then open sections up to remove the trans pink pieces.
Take a White 30cm Bit Light and then thread the connector side through one of the spaces that allow for the cable to be threaded half way down the jet.
Remove the bottom barrel piece and pull the wheel piece down to allow you to thread the rest of the cable through one of the holes in the wheel piece.
Once the cable is thread through, push the wheel piece up and then thread the cable through one of the holes in the barrel piece.
Hold the Bit Light over the centre of the jet and then secure in place by reconnecting the trans pink pieces over the top.
Close the surrounding sections of the jet.
25.) Take the jet section and then thread the cable from the bottom of it through the space at the top of the wing. Pull the cable down from underneath the wing and then thread through the space which leads underneath at the open section.
Pull the cable all the way through and then reconnect the jet section back to the X-Wing.
26.) Repeat the previous two steps to install another White 30cm Bit Light to the upper right jet.
27.) Take another 6-Port Expansion Board and then connect a 5cm Connecting Cable to one of the outside ports.
Take the two Bit Lights from the upper jets and then connect them to available ports on the expansion board we have just used.
28.) Repeat the same process as we did for the upper jets to install another White 30cm Bit Light to the bottom left jet.
Take the cable from the jet and thread though the space which leads inside and then pull down from underneath at the open section.
Reconnect the Jet and then connect the Bit Light from this jet to the next port on the expansion board below (same expansion board as the one used to connect the upper two jets).
29.) Repeat this process again to install the last White 30cm Bit Light to the remaining lower jet and then connect the bit light into the expansion board.
30.) Take the Multi Effects Board and then connect the other end of the 5cm connecting cable (from the expansion board in previous steps) into one of the output ports (side with 2 ports).
In order to configure the effect you want, take the AA battery pack /usb cable and connect the cable into the input port of the effects board (side with one port)
Turn the battery pack on and then turn the switch on the effects board to the far left for the ‘flicker’ effect. Turn the wheel on the effects board to adjust the speed of the effect.
Once you are happy with the effect for the jet lights, carefully disconnect the battery pack cable /usb cable and then move onto the next step.
31.) Take another 5cm Connecting Cable and connect it to the input port on the multi effects board. Connect the other end of the cable into the other 6-port expansion board (where we connected strip lights to)
32.) Tuck the 6-port expansion board (with the bit lights from jets), effects board, and cables into the centre space. Leave the 6-port expansion board (with effects board connected to) out.
Reconnect the 4×8 plate we removed earlier in step 15.
33.) Take the AA Battery Pack /usb cable and connect the cable into the 6-port expansion board we have left out.
Tuck in the expansion board in with the rest of the components, leaving out the battery pack cable /usb cable.
34.) Take the remaining section we removed earlier in step 15 and then disconnect and discard the section with the dark grey 2×6 plate.
Reconnect this remaining section back to cover up the space underneath the X-Wing.
35.) Carefully turn the X-Wing over and then place it back onto the stand with the battery pack placed behind.
This now completes installation of the Light My Bricks Lighting kit for the LEGO UCS Red Five X-Wing.
Here is the user guide instructions for the Light My Bricks Brick Brick Omega Hat Light Kit. Although we have installed this light kit as pictured above, you can install lights to your Brick Hat however you like.
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Instructions for installing this kit
1.) To start, remove the front plate from the hat.
To install the Flashing White Bit Lights, place them over any of the brick studs with the LED facing upward. Secure the light in place by connecting a trans coloured LEGO plate over the top.
You can install Bit Lights anywhere you like as long as they are placed over a stud and secured down using a LEGO plate. You can also connect bricks over the top of the wires to hide them, just ensure the wires are neatly laid in between studs.
2.) If you’d like to install our version of the light kit, then install the 4xFlashing White 15cm Bit Lights to corners as pictured below. You can use any trans coloured plate to connect over the top of the light.
3.) Turn the plate over and then take each of the two cables on each side and then twist them around each other so they form one cable each.
4.) Take the 6-Port Expansion Board and then connect all 4 connectors from each of the lights into the ports on the expansion board.
5.) Take the Flat Battery Pack and insert 2x CR2032 Batteries into it. Connect the battery pack cable into a spare port on the expansion board.
6.) Turn on battery pack on to verify all lights are working OK.
7.) Use tape to secure the expansion board to the bottom of the plate, then place the battery pack in the middle of the plate with the on/off switch facing up. This is so we can easily access the switch to turn on the lights later on when the plate is attached to the hat.
8.) Use more tape to secure down the battery pack as well as the wires.
9.) Attach the plate back to the front of the hat then turn the light kit on and ENJOY!
Here is the instructions document for the LEGO Buckingham Palace LED lighting kit. Please read and follow the steps carefully to ensure this lighting kit is installed properly.
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Instructions for installing this kit
1.) To start, follow the images below to disconnect pieces which make up the main section of the building.
2.) Remove the 4 lamp posts and then disassemble pieces as per below:
3.) To install lights to these lamp posts, take a White 15cm Bit Light and place it directly over the top of one of the posts. Secure the light in place be reconnecting the LEGO pieces over the top.
Bend the cable directly downward as per below
Repeat this process to install another 3x White 15cm Bit Lights to the remaining 3 lamp posts.
Bend the cable upward where it meets the base of the lamp post.
4.) Reconnect the lamp posts ensuring the cables are facing toward the back of the set.
5.) Remove the 2x centre lamp sections and then disassemble as per below
Install another 2x White 15cm Bit Lights to these lamps by using the same method we used to install the previous 4 bit lights to the lamp posts.
Bend both cables downward and then bend them upward approx. 3cm further down.
6.) Reconnect the lamps back to the set ensuring cables are facing toward the back.
7.) Remove the centre statue at the grey round base followed by the larger grey plate underneath.
8.) Remove the following pieces from the top of the plate and then remove the yellow 2×2 plate.
In order for us to install a light underneath this section we will need to discard this yellow 2×2 plate.
9.) Take the Blue 30cm Bit Light and place it facing down in the centre of the base, in between studs.
Ensure the cable is neatly laid in between lego studs, then secure the light in place by reconnecting one of the trans clear 1×2 plates.
Reconnect surrounding pieces we removed earlier and then reconnect this section back to the set.
10.) Turn the base around to the back and then remove the following sections and tiles as we will be laying the cables underneath these.
11.) Lay the blue bit light cable in between studs before reconnecting a tile and gate over the top.
Lay the five cables in the middle in between studs before reconnecting tiles over the top. Ensure that you leave enough room for the cables at the base of each lamp post before reconnecting tiles over them.
Repeat this process for the lamp posts on the sides then reconnect remaining tiles.
12.) Take the two cables in the middle and bend them up in a 90 degree angle before reconnecting the two middle sections as per below ensuring the 2 cables are visible.
13.) Take the 8-port Expansion Board and connect all seven cables to the ports.
Test all lights are working OK by taking the AA battery pack, inserting 3x AA batteries to it, and then connecting the battery pack cable to the remaining port of the expansion board. Turn the battery pack on and check all lights are working OK.
14.) Remove the battery pack and then connect the 15cm Connecting Cable to the remaining port of the expansion board.
15.) We will now reconnect all the sections which make up the building. Start by reconnecting the 2 middle pillar sections as well as the section behind ensuring you place the expansion board in between.
Turn the expansion board around so that it is sitting vertically straight in the centre.
16.) Reconnect the remaining front and side sections of the building
17.) Reconnect the back sections of the building ensuring you leave the other end of the 15cm connecting cable from the expansion board accessible.
18.) Take a White Strip Light and peel off the adhesive backing and stick it onto the base of a provided LEGO 1×6 Plate.
Connect the 15cm connecting cable from the left side of the building into one of the ports on the Strip Light.
Take the left roof section and then mount the Strip Light underneath in the following position.
19.) Take the 5cm Connecting Cable and connect it to the other end of the Strip Light.
Disconnect the centre roof section and then pull the 5cm connecting cable over to the right side
20.) Take another White Strip Light and stick it to another provided LEGO 1×6 Plate. Connect the 5cm connecting cable we pulled across to the left port on the strip light.
21.) Take the right roof section and then mount the strip light underneath in the following position as pictured below. Take the AA Battery Pack and connect the battery pack cable into the right side of the strip light.
Reconnect the right roof section ensuring the battery pack cable is hidden behind and laid in between studs.
Reconnect the middle roof section.
This completes installation of the Buckingham Palace Light Kit. Turn on your light kit and ENJOY!
Here is the instructions document for the LEGO Temple of Airjitzu LED lighting kit. Please read and follow the steps carefully to ensure this lighting kit is installed properly.
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Instructions for installing this kit
1.) We will first install lights to the temple. Start by disconnecting all the surrounding sections then turn the temple around and follow the below images to remove the top 2 levels. First disconnect the top level, followed by the second and first floor sections together.
Remove one of the pillar sections in the top corner then remove the front brick of the base of the fountain at the front of the temple.
2.) Take a Blue 30cm Bit Light and then stick it to the LEGO brick we removed earlier using an adhesive square. Ensure the cable is facing down as per below
Reconnect the brown LEGO brick and then secure the cable in place by disconnecting the other brown LEGO brick opposite, laying the cable and then reconnecting back over the cable. Ensure the cable underneath is laid in between studs.
Reconnect LEGO pieces we removed earlier.
3.) Take the Multi-Effects Board and then connect the Blue Bit Light cable into one of the output ports (side with 2 ports).
To configure the effect, we are going to require power so take the AA Battery pack and insert 3x AA batteries to it. Connect the Battery Pack cable into the input port (side with 1 port) and turn on. Set the switch all to the far left for the “flicker” effect (to give the water fountain a realistic flickering water look) and then turn the wheel to adjust the speed of the effect.
Once you are happy with the speed of the effect, disconnect the battery pack and then proceed to the next step.
4.) Take a 5cm Connecting Cable and then connect it to the output port of the multi-effects board. Connect the other side of the cable to a 6-Port Expansion board.
Take 2x 50cm Connecting Cables and a 15cm Connecting Cable and connect it to available ports on the expansion board.
Take the AA Battery Pack and then connect it to another spare port on the expansion board. Lay the Battery pack down on the bottom of this section as this will be where the battery pack will be permanently set.
Thread one of the 50cm cables out the left side through the spacing in the corner of the building. Pull the cable all the way out from the outside.
Thread the other 50cm cable as well as the 15cm cable out the right side of the building as per below.
5.) Take the first and second level sections of the Temple and reconnect them over the base, then remove the middle section’s floor as per below.
Use the LEGO Removal Tool to disconnect the second level by following the below images.
6.) We will now light up the four red lanterns. Turn the building around and then start with the lantern on the far left. Take a White 15cm Bit Light and then bend the cable down in a 90 degree angle (with the bit light facing out)
With the Bit Light facing the front, place the Bit Light down into the lantern piece ensuring the cable is behind the lantern piece.
Secure the Bit Light in place by threading the cable in towards the building and laying underneath the brown 1×3 plate.
Repeat this step to install another 3x White 15cm Bit Lights to the other 3 lanterns. For the middle two lanterns, use the brown ‘L’ shaped plates to secure the cable in place.
If you find the Bit Lights are easily slipping out of the lanterns, you can secure by using the provided red round plates.
Take the 4x Round Plates 1×1 Red and connect them over the top of each lantern piece to secure the Bit Lights in place and prevent them from slipping out.
7.) Turn the building around to the back and then take an 8-Port Expansion Board and then connect all 4 Bit Light cables into the first few ports toward the left.
Turn on the Battery Pack to test all the lights are working OK.
8.) Take a White Strip Light and then using the adhesive backing, stick it onto the base of a provided LEGO 1×6 Plate.
Connect a 5cm Connecting Cable to the left port and a 15cm Connecting Cable to the right port.
9.) Take the second level of the temple and reconnect if over the bottom level.
Reconnect the floor section we removed earlier.
10.) Take the other end of the 5cm cable we connected earlier to the White Strip Light and connect it to the 8-port expansion board.
Take the other end of the 15cm cable (from the right side of the base)and connect this to another port on the 8-port expansion board.
Using 2x Adhesive Squares, mount the 8-port expansion board as well as the the White Strip Light on to the ceiling of the bottom floor as per below:
You can also use tape to secure cables to the ceiling and prevent them from dangling down.
Turn on the battery pack and verify all is working OK.
12) Take another White Strip Light and stick it on to the base of another LEGO 1×6 Plate. Connect a 30cm connecting cable to the left port and then connect the other end of the 15cm cable from the strip light below into the right port.
Mount the Strip Light to the ceiling of the middle level at the following position. Ensure the connected 30cm cable is facing the inside of the temple.
13.) Take the top level and then reconnect over the second level.
Secure the cable between the ground and second floor in between the flower piece as per below.
14.) Take another White Strip Light and stick it onto the base of a LEGO 1×6 Plate. Connect the 30cm cable from below to the left port.
Eliminate excess cable by winding the cable around the Strip Light 4–5 times before mounting it to the ceiling of the top floor in the below position.
Turn on the Battery Pack to verify all is working OK.
This completes installation of lights for the Temple.
15.) We will now light up the market lanterns which is to the right of the building. Take this market section and then remove the two gold blades which the lanterns are connected to.
Disconnect the bottom white round plates as per below
Take a White 15cm Bit Light and place it directly over the stud of one of the white round plates we disconnected. Secure the Bit Light in place by reconnecting this bottom round plate back to the rest of the lantern ensuring the cable is facing behind.
Repeat this step to install another White 15cm Bit Light to the lantern on the other side.
Reconnect both sections back to the front of the building.
16.) Take the cable from the right lantern and then pull the cable up to bend the cable upward. Lift up the right set of roof tiles and then thread the cable through the space which leads to the left side. Pull the cable out from the left side and then cover the roof back.
Take the left lantern cable and pull it upward. Thread the cable around the brown plate and then loop it back around itself to securely tie the cable.
Take a 6-port Expansion Board and connect both bit light cables to available ports.
17.) Take a White Strip Light and stick it to the base of another LEGO 1×6 plate. Connect a 5cm connecting cable to the left port of the strip light and then connect the other side of the cable to the expansion board.
Thread the strip light through the space inside of the roof and then mount it underneath to the following position.
Mount the expansion board to the inside of the roof using 2x adhesive squares.
18.) Locate one of the 50cm connecting cables from the bottom of the temple and then thread it through the back of the roof of the market.
Pull the cable through and then connect it to a spare port on the 6-port expansion board.
Reconnect both sides of the roof tiles and then reconnect the market base plate to the temple base plate.
Turn the battery pack on to test all the lights are working OK.
19.) We will now light up the cottage on the left of the Temple. Take this section, turn it to the back and remove the second floor.
Remove the two grey plates from the front of the cottage and then place it aside.
20.) Take a White 15cm Bit Light and stick it underneath these 2 plates using an adhesive square. Ensure you stick it in exactly the same position as per below and that the cable is facing toward the back.
With the cable facing behind, carefully reconnect the two plates to the front of the cottage.
The Bit Light should be visible if you look up from underneath.
21.) Take a White Strip Light and stick it to the base of a provided LEGO 1×6 Plate. Connect the Bit Light cable from the front of the cottage to the left port on the strip light. Set this aside for now.
22.) Take another White Strip Light and stick it to the base of another provided LEGO 1×6 plate. Take a 15cm connecting cable and connect it to the left port on the strip light.
Take the second floor of the cottage, turn it to the back and then lift up the left side of the roof.
With the cable facing behind, mount the strip light to the following position on the left side of the roof and then close the roof.
23.) Lift the second floor of the cottage over the base and then lift it up and mount the Strip Light from below underneath in the following position. To eliminate excess cable from the Bit Light, loop it around and secure it in between studs of the 1×6 Plate.
Take the 15cm connecting cable from the second floor and connect this to the right port on the strip light underneath.
You can secure the 15cm cable on the second floor by taping it to the wall.
24.) Locate the other end of the spare 50cm connecting cable from the base of the Temple and connect it to the port on the strip light on the second floor.
Turn the cottage around to the front and then connect the base plate of the cottage to the base plate of the Temple.
This finally completes installation of the Temple of Airjitsu Lighting Kit. Your LEGO set is now ready to come to life.
