Light My Bricks: LEGO Haunted House 10273 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/10273-LEGO-Haunted-House-Front-Light-My-Bricks.jpg)
The following page is the instructions for the Light My Bricks LEGO Haunted House (10273) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Haunted House (10273) LED light kit , please click here to view the product page
Package Contents:
- 4x White 30cm Bit Lights
- 4x White 15cm Bit Lights
- 4x White 30cm Micro Bit Lights
- 12x White 15cm Micro Bit Lights
- 2x Warm White Strip Lights
- 6x Green Strip Lights
- 1x 8-Port Expansion Board
- 3x 6-Port Expansion Board
- 3x Micro 2-4 Port Expansion Boards
- 1x Micro 2-8 Port Expansion Board
- 3x Flicker Effects Boards
- 2x Scary Flicker Effects Boards
- 10x 5cm Connecting Cable
- 2x 15cm Connecting Cables
- 6x 30cm Connecting Cables
- 2x 50cm Connecting Cable
- 1x USB Power Cable
- 4x Adhesive Squares IMPORTANT NOTE: Flat, Round, and AA Battery Packs are unavailable as of June 2022 due to child safety regulations. Please use the 50cm Connecting Cable in place of the Battery Pack.
LEGO Pieces:
- 2x Trans Dark Blue Round Plate 1×1
- 2x Black 1×1 Modified Plate Rounded with Handle
- 1x Black Round Plate with open stud 1×1
- 1x Black Arm Skeleton, Bent with Clips (Horizontal Grip)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) 2.)![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9476-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9505-1024x768.jpg)
Caution – Ensure that you connect Micro Bit Lights to Micro Expansion Board Ports ONLY (smaller ports). Do NOT connect them to regular expansion board ports (larger ports) as this will damage the Micro Bit Lights
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9527-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board or effects board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.Power Bank Note – If your are using the Light My Bricks USB Power Bank, it is normal for the initial lights installed to turn off automatically after a few minutes. This is due to very low power being consumed from the power bank. You won’t have this issue later on when you connect up more lights. 7.) 8.) 9.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9589-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9675-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9807-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9869-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9883-1-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9920-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9945-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9985-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9990-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_9998-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0008-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0035-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0045-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0064-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0068-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0090-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0106-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0194-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0257-768x1024.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0267-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0530-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0516-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0413-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0417-768x1024.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0412-768x1024.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0475-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0499-1024x768.jpg)
This finally completes installation of the Light My Bricks Haunted House 10273 Light Kit.
We thank you for purchasing this product and hope you ENJOY!
Light My Bricks: LEGO Detective’s Office 10246 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/10246-LEGO-Detectives-Office-FRONTOTHER-Light-My-Bricks-300x300.jpg)
The following page is the instructions for the Light My Bricks LEGO Detective’s Office (10246) Lighting Kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Detective’s Office (10246) LED Lighting Kit , please click here to view the product page
Package Contents:
Package contents:
- 6x White Strip Lights
- 5x White 30cm Bit Lights
- 11x Flashing White 30cm Bit Lights
- 1x 12-port Expansion board
- 1x 8-port Expansion board
- 1x 6-port Expansion board
- 1x LEGO Lamp Post With LED Installed
- 6x Adhesive squares
- 6x 15cm connecting cables
- 2x 5cm connecting cables
- 1x USB Power Cable
LEGO Pieces:
- 6x Plate 1×6 (any colour)
- 2x Trans Red Round Plate 1×1
- 1x Trans Dark Blue Round Plate 1×1
Wireless Power Connectors (sold separately)
If you wish to install theIf you wish to use Light My Bricks Wireless Power Connectors in between floors (sold separately), please scroll to the bottom of the page to view the instructions.
You will require the following extra parts (sold separately)
- 3x Wireless Power Connectors sets (Available in 2pk)
- 1x 6-Port Expansion Board
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.)
2.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
3.)
4.)
5.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_2251-1024x768.jpg)
6.)
7.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_2299-1024x768.jpg)
8.)
9.)
10.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.11.)
12.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_2420-1024x768.jpg)
13.)
14.)
15.)
16.)
17.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.18.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_2550-1024x768.jpg)
19.)
20.)
21.)
22.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_2707-1024x768.jpg)
This finally completes installation of the Light My Bricks Detective’s Office 10246 Light Kit.
We thank you for purchasing this product and hope you ENJOY!
Wireless Power Connectors (sold separately)
Follow the below instructions if you wish to install theIf you wish to use Light My Bricks Wireless Power Connectors in between floors. You will require the following extra parts (sold separately)
- 3x Wireless Power Connectors sets (Available to purchase in a 2pk)
- 1x 6-Port Expansion Board
1.)
2.)
3.)
4.)
5.)
6.)
7.)
< END >
Light My Bricks: LEGO Parisian Restaurant 10243 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/6609c-1f2vpsmjmnivfixjmnc-tnq-300x300.jpeg)
The following page is the instructions for the Light My Bricks LEGO Parisian Restaurant (10243) Lighting Kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Parisian Restaurant (10243) LED Lighting Kit , please click here to view the product page
Package Contents:
Package contents:
- 4x White Strip Lights
- 9x White 30cm Bit Lights
- 1x LEGO Lamp Post With LED Installed
- 1x 8-port Expansion Board
- 1x 6-port Expansion Board
- 1x USB Power Cable
- 3x 15cm Connecting Cable
- 2x 30cm Connecting Cable
- 4x Adhesive squares
LEGO Pieces:
- 4x 1×6 Plate (any colour)
Wireless Power Connectors (sold separately)
If you wish to install theIf you wish to use Light My Bricks Wireless Power Connectors in between floors (sold separately), please scroll to the bottom of the page to view the instructions.
You will require the following extra parts (sold separately)
- 1x Wireless Power Connectors (2pk)
- 1x 6-Port Expansion Board
- 2x LEGO Plate 1×6 (any colour)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.)
2.)
3.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1732-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
4.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1751-1024x768.jpg)
5.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1870-1024x768.jpg)
6.)
7.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1816-1024x768.jpg)
8.)
9.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.10.)
11.)
12.)
13.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.14.)
15.)
16.)
17.)
18.)
19.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.This finally completes installation of the Light My Bricks Parisian Restaurant 10243 Light Kit.
We thank you for purchasing this product and hope you ENJOY!
Wireless Power Connectors (sold separately)
Follow the below instructions if you wish to install theIf you wish to use Light My Bricks Wireless Power Connectors in between floors. You will require the following extra parts (sold separately)
- 1x Wireless Power Connectors (2pk)
- 1x 6-Port Expansion Board
- 2x LEGO Plate 1×6 (any colour)
1.)
2.)
3.)
4.)
5.)
< END >
Light My Bricks: LEGO Palace Cinema 10232 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/10232-LEGO-Palace-Cinema-FRONT-Light-My-Bricks-1024x1024.jpg)
The following page is the instructions for the Light My Bricks LEGO Palace Cinema (10232) Lighting Kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Palace Cinema (10232) LED Lighting Kit , please click here to view the product page
Package Contents:
Package contents:
- 5x White Strip Lights
- 15x White 30cm Bit Lights
- 12x Flashing White 30cm Bit Lights
- 3x 12-Port Expansion boards
- 1x LEGO Lamp Post With LED Installed
- 2x 5cm cables
- 3x 15cm cables
- 2x 30cm cables
- 8x Adhesive squares
- 1x USB Power Cable
LEGO Pieces:
- 2x 1×6 Plate (any colour)
Wireless Power Connectors:
If you wish to use Light My Bricks Wireless Power Connectors in between floors (sold separately), please scroll to the bottom of the page to view the instructions. You will require the following extra parts (available for purchase through our DIY range)- 1x Wireless Power Connector set (2pk)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.)
2.)
3.)
4.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
5.)
6.)
7.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1039-1024x768.jpg)
8.)
9.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1074-1024x768.jpg)
10.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1083-1024x768.jpg)
11.)
12.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.13.)
14.)
15.)
16.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1179-1024x768.jpg)
17.)
18.)
19.)
20.)
21.)
22.)
23.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1298-1024x768.jpg)
24.)
25.)
26.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1354-1-1024x768.jpg)
27.)
28.)
29.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1400-768x1024.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
30.)
31.)
32.)
If you wish to use Light My Bricks Wireless Power Connectors in between floors (sold separately), please continue to step 32. otherwise, skip to Step 34.
32.)
33.)
34.)
35.)
36.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1553-1024x768.jpg)
37.)
38.)
If you wish to use Light My Bricks Wireless Power Connectors in between floors (sold separately), please continue to step 39. otherwise, skip to Step 41.
39.)
40.)
41.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.42.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_1657-1-225x300.jpg)
This finally completes installation of the Light My Bricks Palace Cinema 10232 Light Kit.
We thank you for purchasing this product and hope you ENJOY!
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/10232-LEGO-Palace-Cinema-FRONT-Light-My-Bricks-1-1024x1024.jpg)
Light My Bricks: LEGO Volkswagen T1 Campervan 10220 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/10220-LEGO-Light-Kit-Volkswagen-T1-Camper-Van-FRONT-Light-My-Bricks-1024x1024.jpg)
The following page is the instructions for the Light My Bricks LEGO Volkswagen T1 Campervan (10220) Lighting Kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Volkswagen T1 Campervan (10220) LED Lighting Kit , please click here to view the product page
Package Contents:
- 10 x White 30cm Bit Lights
- 1 x 12 Port Expansion board
- 1 x USB Power Cable USB Power Cable has replaced Flat & Round Battery Packs (CR2032) as of June 2022 due to child safety regulations. Please use the USB Power Cable in place of the Battery Pack.
LEGO Pieces:
- 4x Black 2×4 Plates
- 2x Black 2×6 Plates
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.)
2.)
3.)
4.)
5.)
6.)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
7.)
8.)
9.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0778-1024x768.jpg)
10.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0746-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0752-1024x768.jpg)
11.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0782-1024x768.jpg)
12.)
13.)
14.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0837-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0843-1-1024x768.jpg)
15.)
USB Power Cable has replaced Flat, Round, and AA Battery Packs as of June 2022 due to child safety regulations. Please use the USB Power Cable in place of the Battery Pack.
If using the USB Power Cable, plug it into the same port on the Expansion Board as is shown with the Battery Pack. Then, run the USB Cable out from underneath the van.![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0852-1024x768.jpg)
16.)
17.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/07/IMG_0874-1024x768.jpg)
18.)
This finally completes installation of the Light My Bricks Volkswagen T1 Campervan 10220 Light Kit.
We thank you for purchasing this product and hope you ENJOY!
Light My Bricks: LEGO UCS A-Wing Starfighter 75275 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/75275-LEGO-UCS-A-Wing-Starfighter-Left-Angled-Light-My-Bricks.jpg)
The following page is the instructions for the Light My Bricks LEGO UCS A-Wing Starfighter (75275) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO UCS A-Wing Starfighter (75275) LED light kit , please click here to view the product page
Package Contents:
- 8x Warm White 30cm Large Bit Lights
- 4x Cool White 30cm Bit Lights
- 2x Red 30cm Bit Lights
- 1x White Strip Light
- 1x 12-Port Expansion Board
- 1x 8-Port Expansion Board
- 1x 2-Port Expansion Board
- 1x Pulse Effects Board
- 1x Gun Effects Board
- 3x 5cm Connecting Cable
- 1x 15cm Connecting Cables
- 1x 30cm Connecting Cable
- 1x USB Power Cable
LEGO Pieces:
- 2x Trans Clear Plate 1×1
- 1x Trans Clear Round Plate 1×1
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) 2.) 3.)![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_8893-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.Power Bank Note – If your are using the Light My Bricks USB Power Bank, it is normal for the strip light to turn off automatically after a few minutes. This is due to very low power being consumed from the power bank. You won’t have this issue later on when you connect up more lights. 7.) 8.) 9.) 10.) 11.) 12.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9052-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9121-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9184-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9185-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9249-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9252-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9265-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9273-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/06/IMG_9289-1024x768.jpg)
This finally completes installation of the Light My Bricks UCS A-Wing Starfighter Light Kit.
We thank you for purchasing this product and hope you ENJOY!
Protected: Laying Cables
Light My Bricks: LEGO Dom’s Dodge Charger 42111 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2023/02/42111-LEGO-Doms-Dodge-Charger-lights-on-Light-My-Bricks.jpg)
The following page is the instructions for the Light My Bricks LEGO Dom’s Dodge Charger (42111) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Dom’s Dodge Charger (42111) LED light kit , please click here to view the product page
Package Contents:
- 4x Warm White 30cm Large Bit Lights
- 2x White 30cm Bit Lights
- 2x Orange 30cm Bit Lights
- 6x White 15cm Bit Lights
- 1x Warm White Strip Light
- 1x 12-Port Expansion Board
- 1x 8-Port Expansion Board
- 1x NC Push Board
- 1xFlicker Effects Board
- 1x 5cm Connecting Cable
- 2x 15cm Connecting Cables
- 1x 30cm Connecting Cable
- 1x USB Power Cable
LEGO Pieces:
- 2x Trans Orange Round Plate 1×1
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) 2.)![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8082-1-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8089-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8098-1-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8118-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8145-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8159-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.Power Bank Note – If your are using the Light My Bricks USB Power Bank, it is normal for the strip light to turn off automatically after a few minutes. This is due to very low power being consumed from the power bank. You won’t have this issue later on when you connect up more lights. 7.) 8.) 9.)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8229-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8264-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8269-1-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8387-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8391-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8422-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8450-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8490-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8500-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8504-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8514-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_8516-1024x768.jpg)
This finally completes installation of the Light My Bricks Dom’s Dodge Charger Light Kit.
We thank you for purchasing this product and hope you ENJOY!
Light My Bricks: LEGO Pirates of Barracuda Bay 21322 Lighting Kit
![](http://guides.lightmybricks.com/wp-content/uploads/2020/04/21322-LEGO-Pirates-of-Barracuda-Bay-Front-Light-My-Bricks.jpg)
The following page is the instructions for the Light My Bricks Pirates of Barracuda Bay (21322) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Pirates of Barracuda Bay (21322) LED light kit , please click here to view the product page
Package Contents:
Bit Lights
- 6x White 30cm Bit Lights
- 6x White 15cm Bit Lights
- 2x White 30cm Micro Bit Lights
- 5x White 15cm Micro Bit Lights
- 1x Green 30cm Bit Lights
Strip Lights
- 4x Warm White Strip Lights
- 4x Blue Strip Lights
- 1x Green Strip Light
Expansion Boards
- 1x 2-Port Expansion Board
- 3x 6-Port Expansion Boards
- 1x 8-Port Expansion Board
- 2x Micro 2-4 Port Expansion Boards
- 2x Flicker Effects Boards
Connecting Cables
- 5x 5cm Connecting Cables
- 6x 15cm Connecting Cables
- 4x 30cm Connecting Cables
- 2x 50cm Connecting Cables
- 1x USB Power Cable
LEGO Pieces:
- 1x Trans Clear Plate w Rounded Bottom 2×2
- 2x Black Round Plate 1×1 with Open Stud
- 2x Black Tile 1×1 with Clip Rounded Edges
- 2x Black 1×1 Modified Plate Rounded with Handle
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) We will begin with lighting the left section first. Seperate the two sections, then disconnect the front of the ship via the ball joints. Disconnect the following black bricks from underneath the ship, then disconnect the following 2×4 plate from the top. 2.) Take a Green Strip Light and connect a 30cm Connecting Cable to the left port, then connect a 15cm Connecting Cable to the right port. Thread both cables up underneath the first floor, then pull both cables out from the top. Peel off the adhesive backing from the green strip light and stick it underneath the first floor in the following position.![](http://guides.lightmybricks.com/wp-content/uploads/2020/04/IMG_7140-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/04/IMG_7152-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.Power Bank Note – If your are using the Light My Bricks USB Power Bank, it is normal for the strip light to turn off automatically after a few minutes. This is due to very low power being consumed from the power bank. You won’t have this issue later on when you connect up more lights. 4.) Disconnect the lamp from the front side of this section, then disassemble it as per below. Take a White 30cm Bit Light and thread the connector side of the cable through the base (larger hole) of the trans yellow round brick. Thread the cable through, then slightly bend the LED onto a 90 degree angle so that it will eventually point directly down when the lamp is reconnected. Pull the cable all the way from the top of the trans brick so that the LED sits comfortably inside, then thread the connector end of the cable through the base of the lamp enclosure. Pull the cable out from the outside, then reconnect the trans yellow brick inside. 5.) Reconnect the lamp to the lamp post, then pull the cable over the top post and then bring the cable back down and thread the cable between the two black clips. Reconnect the lamp to the deck, then thread the cable underneath. Pull the cable all the way out from behind, then thread it through the back of the deck (in between the rock and the tree trunk) Disconnect the following pieces and lay the cable down in between studs before reconnecting these pieces over the top. Take the front section of the ship and reconnect the black bricks underneath. Connect the ship back to the set via the ball joints, then turn the set around and connect the Bit Light cable from the lamp to the 6-port expansion board. Turn the power ON to test the lamp LED is working OK. 6.) Take a 15cm Connecting Cable and connect one end of the cable to the 6-Port Expansion Board. Thread the other end of the cable through to the left (behind the post that is attached to the rigging). Bring the cable underneath the ships’s kitchen, then connect the cable to a Blue Strip Light. Take a 30cm Connecting Cable and connect it to the Blue Strip Light’s left port. Peel off the adhesive backing and mount the strip light underneath the ship in the following position. Thread the other end of the 30cm Cable through to the outside of the ship, then pull the cable down and thread it in between the deck post and deck base. Pull the cable all the way out as shown below. 7.) Disconnect the lamp post section from the front, then disconnect the following two larger brown plates. Take the 30cm Connecting cable from the side and thread it underneath the deck, then lay it around the following studs of the deck post. Reconnect one of the larger brown plates over the top as shown below. 8.) Disassemble the lamp section as per below, then repeat the same method used for the previous lamp to install another White 30cm Bit Light to it. 9.) Locate the 30cm Connecting Cable from underneath the deck and connect it to a Blue Strip Light. Connect the Bit Light cable from the lamp post to the other port on the blue strip light. Reconnect the lamp post to the front of the large brown plate that sits at the front of the deck, then turn it over so we can access underneath of it. Using the adhesive backing, stick the Blue Strip Light underneath this plate in the below position. Twist/Fold the excess cable from the Bit Light and Connecting Cable into neat bunches, then turn the plate over and tuck the cables neatly underneath the plate behind. Reconnect the large brown plate, then disconnect the brown tile at the front and further tuck in any excess cable before reconnecting the tile. Turn ON the power to test all the lights installed so far are working OK. Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide. 10.) From the back of this section, remove the top floor above the captain’s HQ, then locate the spare end of the 30cm Connecting Cable from the Green Strip Light below and bring it up above the top floor. Slip the cable in between the yellow plates on the right and connect it to an 8-Port Expansion Board. Disconnect the two lamps, then repeat the same method used for the previous lamps to install this time, a White 15cm Bit Light to each lamp (Total 2x White 15cm Bit Lights) 11.) Reconnect one of the lamps to the side of the ship, then follow the below images to disconnect the surrounding pieces. Bring the lamp cable through to the inside of the captain’s HQ and lay it down in between studs before reconnecting all the pieces we removed earlier. 12.) Take the other lamp post and loop the cable around the top of the lamp post. Disconnect the railing section above the door, then reconnect the lamp post to it. Thread the cable through the railing and pull it all the way out from the other side before reconnecting this section back to the top of the ship. Disconnect the following brown tile and lay down the cable from the lamp above in between studs, before reconnecting the tile over the top. Connect the two lamp cables to the 8-Port Expansion Board. Turn ON the power to test the lamp lights are working OK.
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7286-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.13.) From the front of the set, disconnect the front panel on the top floor as well as the two lamp sections. Disassemble one of the lamps, then take a White 30cm Bit Light and thread the connector side of the cable through the base of the trans yellow brick (larger hole). Place the LED all the way inside the brick (without bending it on a 90 degree angle like we did earlier). With the LED facing the inside wall of the trans yellow brick, carefully reconnect the black bar through the larger hole of the brick. You will notice the bar will be on a slight angle because of the LED pushing against it. This is normal. Do not forcefully push the black bar all the way through, we just need the bar to be pushed in enough to stay secure. Pushing the bar the whole way through may break the cable.
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7301-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7305-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7307-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7321-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7322-1024x768.jpg)
- 1x Black Round Plate 1×1 with Open Stud
- 1x Black Tile 1×1 with Clip Rounded Edges
- 1x Black 1×1 Modified Plate Rounded with Handle
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7397-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7408-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7349-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7432-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7472.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7472-1-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7471-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7854-768x1024.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7855-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light, expansion board or effects board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.Disconnect the USB Power Cable from the 6-Port Expansion Board as we will use this to test the lights we install to the right section of this set. 27.) We will now move onto the right section. First remove the ship from the dock by disconnecting it from the technic pins on the dock and pulling it all the way out.
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7479-768x1024.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7524-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7533-1024x768.jpg)
Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
30.) Connect the spare end of the 15cm Connecting Cable from the Blue Strip Light to a new Blue Strip Light, then leave this aside for now as we will stick this strip light underneath the ship later on. Disconnect the USB Power Cable from the expansion board as we will use this to test lights we are about to install to the ship. 31.) Disconnect the following square plate from the ship’s deck, then un-clip the bottom of the rope ladder to allow us to completely remove the square plate along with the mast.![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7554-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7570-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7599-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7628-1024x768.jpg)
38.) Disconnect the USB Power Cable from the 6-Port Expansion Board, then twist/fold the micro bit light cables into a neat bunch. Bring all the expansion boards together and twist the two 5cm connecting cables into a neat bunch. 39.) Take the front panel section and disconnect the lamp post. Using the same method used to install previous lamp lights, install a White 15cm Bit Light to it. Wind the cable around the lamp post as shown below, then reconnect it to this section. Turn this section onto it’s back so we can access underneath of it. Connect the Bit Light cable to the left port on a Warm White Strip Light, then connect a 15cm Connecting Cable to the right port. Using it’s adhesive backing, stick the strip light underneath this section in the following position, then neaten up the excess cable from the Bit Light by twisting/folding it into a neat bunch. 40.) Reconnect the panel to the plate underneath, then tuck the 15cm connecting cable underneath and in between the panel and the plate before reconnecting this section to the top of the ship.Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light, expansion board or effects board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7690-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7702-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7711-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7738-768x1024.jpg)
- 1x Black Round Plate 1×1 with Open Stud
- 1x Black Tile 1×1 with Clip Rounded Edges
- 1x Black 1×1 Modified Plate Rounded with Handle
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7397-1024x768.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7758-768x1024.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7780-768x1024.jpg)
![](http://guides.lightmybricks.com/wp-content/uploads/2020/05/IMG_7819-1024x768.jpg)
This finally completes installation of the Light My Bricks Pirates of Barracuda Bay Light Kit.
We thank you for purchasing this product and hope you ENJOY!