The following page is the instructions for the Light My Bricks LEGO UCS A-Wing Starfighter (75275) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO UCS A-Wing Starfighter (75275) LED light kit , please click here to view the product page
Package Contents:
- 8x Warm White 30cm Large Bit Lights
- 4x Cool White 30cm Bit Lights
- 2x Red 30cm Bit Lights
- 1x White Strip Light
- 1x 12-Port Expansion Board
- 1x 8-Port Expansion Board
- 1x 2-Port Expansion Board
- 1x Pulse Effects Board
- 1x Gun Effects Board
- 3x 5cm Connecting Cable
- 1x 15cm Connecting Cables
- 1x 30cm Connecting Cable
- 1x USB Power Cable
LEGO Pieces:
- 2x Trans Clear Plate 1×1
- 1x Trans Clear Round Plate 1×1
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.)Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.Power Bank Note – If your are using the Light My Bricks USB Power Bank, it is normal for the strip light to turn off automatically after a few minutes. This is due to very low power being consumed from the power bank. You won’t have this issue later on when you connect up more lights. 7.)
This finally completes installation of the Light My Bricks UCS A-Wing Starfighter Light Kit.
We thank you for purchasing this product and hope you ENJOY!