![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/10259-LEGO-Winter-Village-Station-Left-Corner-Light-My-Bricks-1-300x300.jpg)
The following page is the instructions for the Light My Bricks LEGO Winter Village Station (10259) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Winter Village Station (10259) LED light kit , please click here to view the product page
Package Contents:
- 7x White 30cm Bit Lights
- 6x White 15cm Bit Lights
- 4x White Strip Lights
- 1x Multi Colour Light String
- 1x 8-Port Expansion Board
- 1x 12-Port Expansion Board
- 2x 5cm Connecting Cables
- 2x 15cm Connecting Cables
- 1x AA Battery Pack (requires 3x AA Batteries)
- 1x Flat Battery Pack (requires 2x CR2032 Batteries)
LEGO Pieces:
- 4x Plate 1×6 (Any Colour)
- 2x White Plates 1×4
- 2x Trans Clear Round Plate 1×1
- 2x Trans Orange Round Plate 1×1
- 1x Trans Clear Plate w Rounded Bottom 2×2
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Install lights to the Bus
1.) We will start by installing lights to the bus. First take the bus and disconnect the roof as well as the following pieces so we can access the headlights.
Remove the trans clear round tile from each headlight then take a White 15cm Bit Light and place it over the top of one of the headlight pieces. Secure the Bit Light in place by connecting a provided Trans Clear Round Plate 1×1 over the top then fold the cable down the side. Repeat this process to install another White 15cm Bit Light to the other headlight, securing it in place using another provided Trans Clear Round Plate 1×1.![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_0932-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_0950-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_0972-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_0973-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_0986-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_0989-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1006-300x225.jpg)
Install lights to the Winter Village Station
1.) We will first install lights to the lamp posts on each side. Disconnect both of these and then dissemble one of them as shown below. 2.) Take a White 30cm Bit Light and place it in the middle of the studs on the base side of the black round 2×2 plate (with rounded bottom). Secure the bit light in place by reconnecting the trans yellow cone piece over the top then reconnect the trans clear cover. Thread the connector end of the cable through the top of the black brick and then pull it out from the back as shown below: Pull the cable all the way through before reconnecting the lamp to the black brick ensuring the cable is facing the back. 3.) Reconnect the lamp post to the right side of the station then wind the cable around the pole twice. Secure the cable down by laying it underneath the lamp post base in between studs with the cable facing the right side then thread the cable through to the back of the station. From the back of the station, secure the cable underneath the black base section and then bring it under and secure in between the platform and platform base as shown below: 4.) Repeat previous steps to install another White 30cm Bit Light to the other lamp post. Reconnect the lamp post to the left side of the station then wind the cable around the pole twice. Secure the cable down by laying it underneath the lamp post base in between studs with the cable facing the back side. Bring the cable toward the back of the station and then secure it in between bricks underneath the platform base as shown below. 5.) We will now install a light above the main entrance door to shine down. Take a White 30cm Bit Light and thread the connector end of the bit light through the space above the door as shown below: Thread it all the way through and pull it out from the inside of the station. With the LED facing down, push the bit light up the following hole then secure the Bit Light in place by taking a provided Trans Clear Plate w Rounded Bottom 2×2 and connecting it to the ceiling above the doorway as shown below. The Bit Light should be visible and in between the studs of the trans clear plate. 6.) From the back of the station, bring the cable from the bit light we just installed toward the right and then secure it underneath the Winter Village schedule plate ensuring the cable is laid in between studs. 7.) Take a 12-Port Expansion Board and connect this bit light cable, along with the two bit light cables from the lamp posts to the first few ports. Take the AA Battery Pack and insert 3x AA Batteries. Connect the battery pack cable to the expansion board and then turn the battery pack ON to test all the lights we have installed so far are working OK. 8.) We will now install a light above the ticket window. Carefully disconnect the front of the roof section to create a gap just above the window. Take a White 30cm Bit Light and thread the connector side of the cable through this space we have created. Pull the cable all the way out from the other side and then push the Bit Light up inside the hole of the ceiling as shown below (with LED facing down). Close up the gap by reconnecting the roof section to secure the Bit Light in place. 9.) Disconnect the entrance door bit light from the expansion board then group together this Bit Light along with the ticket booth Bit Light and twist/wind them around each other so they come together to form one larger cable. Bring the large cable down the side of the building, then bring it under the platform and secure it in between plates. Connect both cables to the 12-port expansion board Turn the Battery Pack ON to verify the light above the ticket window is working OK![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1130-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1137-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1141-e1540433968882-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1159-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1200__1_-1-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1202-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1729-2-300x225.jpg)
![](http://guides.lightmybricks.com/german/wp-content/uploads/2018/10/IMG_1197-300x225.jpg)
This finally completes installation of your Light My Bricks Winter Village Light Kit. We hope you enjoy and we thank you for purchasing this product.